A BEGINNER'S GUIDE TO INSTALLING A BATHTUB

A Beginner's Guide to Installing a Bathtub

A Beginner's Guide to Installing a Bathtub

Blog Article

Click Here

Are you currently looking for additional info on How to Install a Bathtub?


A Step-by-Step Guide to Installing a Bathtub
Installing a tub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old tub with a brand-new one is additionally a reasonably challenging job. If the old bathtub is readily accessible, the job can move rapidly; if you have to open up a wall to eliminate the old tub and position the new bathtub, the task is much harder. In either situation, the task is within a house handyman's skills, although you will certainly require an assistant to leave the old tub and also embeded in the new one. Ensure you have actually certified on your own for the task and also are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is better to consider utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube connections.
This post will certainly help you mount a new tub in your shower room if you have already gotten a brand-new bathtub and also don't need to alter the arrangement of your previous supply of water pipelines.
Your devices and also material checklist should make up the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Planning for the Installation


    First of all, the sustaining framework provided with the bathroom needs to be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to prevent stress on the bathtub.
    Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last setting.

    Removing Old Taps


    If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of removing the existing taps can be quite problematic as a result of the limited access that is typically the situation.
    Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipes have been eliminated, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old securing substance.
    Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

    Setting up the Bathtub


    Using the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little points.
    The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bath tub till the spirit level reads level.
    To install faucets, fit all-time low of the furthest versatile faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
    Activate the supply of water as well as examine all joints and also brand-new pipework for leakages as well as tighten them if required. Load the bathtub as well as also inspect the overflow outlet and the regular outlet for leaks.
    Ultimately, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the bathtub should wait up until the bathtub has actually been made use of at the very least once as this will resolve it right into its last position.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipelines.
    If you require to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next, position the tap in the installing hole in the bath/basin ensuring that the washers are in location in between the tap and also the sink. Secure the faucet in place with the manufacturer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The previous type should be attached to the tap finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Tiling Around the Bath tub


    In the area where the bath fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to break a stiff seal, causing the water to permeate the wall in between the bathroom as well as the tiling, causing issues with wetness as well as feasible leakages to the ceiling below.
    You can pick from a range of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split relatively early if you do not take into consideration this movement prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant glue and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I came across that review about How to Install a Bathtub when doing a search on the web. Are you aware of somebody who is looking into the subject? Feel free to share it. I thank you for reading our article about Installing A Bathtub.


    Clog problems? Inform.

    Report this page